|
Post by flammablehero on Aug 19, 2019 21:09:48 GMT
This is probably a stupid question, and I think I already know he answer, but are new AoS models basically the same size as EE models? In particular, I really dig the new Ironbreakers/Ironsdrake models. I assume the Dispossessed Dwarf models are the same spruces as EE dwarfs but with just round 25mm bases.
I assume all of AoS uses 25mm round bases as standard, but before I commit to dropping $50 for a box, I want to make sure they won’t be oversized for 20x20mm squares.
Thanks.
|
|
|
Post by crownprinceimrik on Aug 19, 2019 21:20:15 GMT
The Ironbreakers/Irondrakes are not new models released for Age of Sigmar, they were released for 8th Edition and then later repackaged with round bases for Age of Sigmar. They fit perfectly on 20mm squares as that's what they were designed for.
In other areas the AoS models tend to be larger. They may not physically be larger, but their more dynamic and aggressive poses make them difficult to fit on smaller bases, while in other cases they models just are in fact scaled up to be a bit larger.
|
|
|
Post by flammablehero on Aug 19, 2019 22:02:46 GMT
That’s what I figured/hoped. Thanks.
|
|
|
Post by knoffles on Aug 23, 2019 7:09:43 GMT
|
|
|
Post by DiscoQing on Aug 23, 2019 10:05:16 GMT
Here's the Slayer hero guy on a square too. Just need to angle him right when in a unit lol...
|
|
|
Post by lordofskullpass on Aug 24, 2019 11:08:29 GMT
I tried making some Vulkite Berzerkers on 20mm bases to use as Slayers in Fantasy, and they turned out pretty well once I had ordered them up properly:
|
|
|
Post by flammablehero on Aug 25, 2019 14:36:25 GMT
|
|
|
Post by knoffles on Aug 28, 2019 8:32:24 GMT
ive used them once and it took over three months to receive my order (with much chasing). The minis themselves are ok. Not the best quality but not the worst either. You can pretty much see what they are like from the photos. mottdon also bought a few of their minis and his delivery time was less than mine (and he’s on a different continent!). The shipping times do seem to be a consistent complaint on the FB pages too (though I will say that not for everyone).
|
|
|
Post by mottdon on Aug 28, 2019 12:47:49 GMT
ive used them once and it took over three months to receive my order (with much chasing). The minis themselves are ok. Not the best quality but not the worst either. You can pretty much see what they are like from the photos. mottdon also bought a few of their minis and his delivery time was less than mine (and he’s on a different continent!). The shipping times do seem to be a consistent complaint on the FB pages too (though I will say that not for everyone). Yep, what knoffles said. I got their Teutogen Guard alternatives. You can see how they match up in my Empire thread.
|
|
|
Post by flammablehero on Aug 28, 2019 13:11:17 GMT
ive used them once and it took over three months to receive my order (with much chasing). That's unfortunate to hear. I went ahead and ordered 20 of their Irondrake equivalent after that post. I figured at around half the cost of 10 Irondrakes from GW, it was worth a try. Even at that price, the prospect of waiting 3 months is disheartening. At this point, I ordered some Shieldbreakers from Kings of War as Hammerers, but I was highly disappointed in the models. The photos were OK but when I got the models, the hands didn't actually close around the weapons and looked funny, so I sent them back. I did order some Kings Guard from Avatars of War that so far I've been satisfied with. My intention is to do some major converting/kitbashing/green-stuffing to turn them into Ironbreakers, take their weapons and convert some cloaked warriors with faceplates into Hammerers. I've been out of WFB for about 13 years, and I was just getting into Dwarfs right around the time they released the 7th (& 8th) Dwarf warrior models. I picked up several boxes as wall as the battalion and army box that was available at the time. So i've got around 40 6th edition warriors, 80 7th edition warriors. My thought was to treat 6th edition as basic clansmen/warriors. Thematically, since the models are relatively basic, they would represent the artisans/masons/smiths/etc that are not standing army to issue out to defend the Hold. Since the 7th edition warriors were a little more detailed, I'm keeping them as Longbeards and I'd like to convert some to Hammerers. I like the ID/IB models from GW, but I don't like the fact that LB and Hammerers look like they have the same gromril armor. Since LB and Hammerers only have heavy armor, I think it makes sense their armor wouldn't look like full-plate gromril, but with like heavy armor/chain mail with more details. I'm only using cloaked models for the Hammerers with then intention to paint them with a celtic-knot pattern and the dwarf face-plates to give them that more "elite/bodyguard" feel. Personally, I don't want my LB and Hammerers so much look like the ID/IB tanks. Part of my goal is also hobbying on a budget. Back in the day, I couldn't justify spending a lot of money on metal Questing Knights (despite how cool they looked), so I converted KotR to use great axes.
|
|
|
Post by sedge on Aug 28, 2019 14:17:38 GMT
I've never ordered from Norba before, but they seem okay. They have a thread over on the 9th age forum that I follow - the people who run it seem to be making an effort to improve, and they're also replacing much of their older poor quality resin sculpts with new multi-part plastic kits that'll be coming in the next few months. Of the non-GW miniature companies out there, they look like one of the most promising.
|
|
|
Post by flammablehero on Aug 29, 2019 13:18:52 GMT
|
|
|
Post by flammablehero on Sept 3, 2019 21:35:56 GMT
ive used them once and it took over three months to receive my order I just got my order today. Only took about a week. And that’s shipping across the Atlantic. I guess I must have gotten lucky with their shipping schedule.
|
|
|
Post by knoffles on Sept 4, 2019 15:49:49 GMT
Good to know that either delays may not be the norm or that they may have improved things (my order was at least a year and a bit ago)
|
|